Spare Parts

Tork Craft Imp. Selector Knob & Change Over Plate (26-28) Service Kit For TCID1100 At a Glance: Replacement selector knob and change-over plate kit (parts 26–28) for forward/reverse control on the Tork Craft TCID1100 Forward/reverse selection should feel definite—click, engage, done. If your TCID1100 selector is loose, sticky, or won’t shift cleanly, you can end up with partial engagement (which is the mechanical version of “maybe”) and that’s bad for control and for internal parts. The To..

Tork Craft Inductance Long & Short (21/22) Service Kit For TCID0850 At a Glance: Replacement inductance components (parts 21 and 22) for the Tork Craft TCID0850 impact driver electrical system Inside many power tools, inductance coils (often called chokes) do an unglamorous but important job: they help smooth electrical behaviour, reduce interference, and protect the tool’s electrical system from spikes and noise created during operation. If your TCID0850 has electrical faults, intermitten..

Tork Craft Intermediate Spindle & Helical Gear Kit (29-34) Service Kit For TCID1100 At a Glance: Intermediate spindle and helical gear kit (parts 29–34) for the Tork Craft TCID1100 gearbox drive train Inside the TCID1100 gearbox, the intermediate spindle and helical gear components do the heavy lifting of transferring power smoothly through the gear train. When these parts wear, you’ll often notice extra noise, rough running, slipping under load, or that “gritty” feel that suggests the gea..

Tork Craft Magnet & Motor Switch Set (43/45) Stand Service Kit (TCMD0035WO-SK23) At a Glance: Replacement magnet and motor switch set for the TCMD0035WO—diagram parts (43/45) for reliable holding power and dependable start/stop control. A mag base drill’s two non-negotiables are simple: the magnet must hold and the motor must respond. If either switch becomes intermittent, sticky, or unreliable, you end up with unpredictable behaviour—and that’s not just annoying, it’s unsafe...

Tork Craft Magnet and Motor Switch Set (61 63) Stand Service Kit At a Glance: Replacement magnet and motor switch set (parts 61 & 63) for safe control and dependable operation Magnetic base drills don’t do “maybe” — the magnet and motor controls need to be positive, reliable and consistent every single time. If a switch feels loose, sticks, arcs, becomes intermittent, or simply refuses to behave, it’s time to replace it before it becomes a safety problem. The Tork Craft Magnet and Motor Switch..

Tork Craft Magnet & Motor Switch Set (61/63) Stand Service Kit (TCMD0035QE-SK025) At a Glance: Replacement magnet and motor switch set for the TCMD0035QE—diagram parts (61/63) for reliable holding power and dependable start/stop control. A mag base core drill has two “must-work-every-time” controls: the magnet (for secure holding) and the motor (for predictable drilling power). If either switch becomes intermittent, sticky, or unreliable, the whole job turns into guesswork—and..

Tork Craft Main Body For Drill Stand TC04700 (TC04700B) At a Glance: Genuine replacement main body casting for the TC04700 drill stand Give your Tork Craft drill stand a second life by replacing the hard-working main body casting instead of the complete stand. This genuine TC04700B spare part is designed to match the original TC04700 drill stand for portable drills, restoring rigidity, alignment and stability when the original body has been damaged, worn or cracked through years of servi..

Tork Craft Motor & Electronics Complete Kit (10-18/31) For TC20171 Impact Wrench At a Glance: Matched motor and electronics kit for the TC20171 20V brushless impact wrench When your Tork Craft IW450 impact wrench starts to lose power, cut out or refuse to switch on, the problem is usually deep inside the motor or electronics. The TC20171-SK02 Motor & Electronics Complete Kit (10–18/31) gives you a genuine Tork Craft replacement pack that brings the main motor and control electronics toge..

Tork Craft Motor Housing Kit (31, 37-39) For TCRH0800 (TCRH0800-SK05) At a Glance: Motor housing kit covering reference parts (31 and 37–39) for the Tork Craft TCRH0800. A rotary hammer’s housing does more than keep things looking tidy—it holds the motor assembly in alignment, protects wiring and components, and keeps everything stable while vibration and impact do their thing. If the housing is cracked, warped, or the screw mounts are stripped, you can end up with loose fitment, extra vib..

Tork Craft Nut & Stop Lever (10, 11) Service Kit (TCMD0068HD-SK03) At a Glance: Replacement nut and stop lever components for reference parts (10 and 11) on TCMD0068HD mag base drills. On a mag base drill, small control parts make a big difference. A stop lever helps you set limits and repeat operations consistently, while the nut secures the assembly so settings don’t wander mid-job. If the lever is bent, worn, or the nut threads are damaged, you can end up with slipping adjustments, inco..